Sweepers & Slashers
Hydraulic Road Works Brooms
"EXCELLENCE
IN ROAD BROOM ENGINEERING AND DESIGN"
Manufactured by Bonne Engineering (Aust) Pty Ltd.
in Australia.
Trailer Brooms
Save the cost
of a tractor!!
May be towed by road vehicles from 1.5 Tonne
towing capacity upwards or tractors.
| Model |
SE6T |
| Sweep
Width |
2000mm |
| Brush
Diameter |
860mm |
| Sweep
Angle |
30°
L/R |
| Brush
Type |
Poly,
Steel, Poly/Steel Mix |
| Features: |
High Performance
Low Maintenance
Low Brush Wear
|
Accurate brush down travel
stop setting for brush
to work
pressure reduces brush wear
Fitted with Diesel Engine
Remote controlled by cable or wireless
Electric Brakes
|
Electric Start
Tail stop and signal lights
Mudguards ready for registration
Powder coat finish
600 x 14" x 8 Ply truck tyres
|
For sweeping operation, this
broom may be towed by a variety of road vehicles with a towing
facility. Tow hitch is adjustable to suit a range of towbar
heights for utilities, trucks and tractors. Tow adaptors to
suit ball, pintle hook and ring feeder are available.
Remote control operated raising, lowering and
angling of brush. Camber adjustment at tow hitch.
Rubber torsion independent suspension allows
trailer broom to be towed at highway speeds.
Close coupled hydraulic pump and direct coupled
hydraulic wheel motor (no chains, shaft or gear drive) eliminate
high maintenance components.
Trailer brooms are readily towed from
site to site resulting in substantial cost and time savings
for relocation by eliminating road transport. Road clean ups
after collisions are carried out quickly and effortlessly.
Tractor Mount Brooms
Low Maintenance - Proven
Performance
Stanbar Three Point Linkage brooms are fully
hydraulic with direct coupled hydraulic drive. The brush carrier
(axle) is direct “Quick Coupled” to the hydraulic
wheel motor thereby eliminating high maintenance gearboxes,
driveshafts, chains and sprockets and ALLOWING QUICK and SIMPLE
BRUSH REPLACEMENT.
The brooms feature nylon bushed hinged frame
design that prevents weight of the tractor transferring to
the broom when tractor bounce occurs. The single trailing
swivel wheel grades the brush to the work, eliminating skipping
of aggregate experienced with rigid frame brooms. The trailing
wheel swivels 360° on taper roller bearings. The trailing
wheel stub axle also has taper roller bearing and is fully
roadable.
SE6 and SE4 Models also feature an hydraulic
oil “Flow Control Valve” to allow brush speed selection
to suit particular phases of sweeping work and compensates
for brush wear speed reduction.
|
Three
Point Linkage
To suit tractors up to 40H.P. and above
|
|
| Models
SE4,SE4R, & SE6, SE6R |
|
|
| |
Medium/Heavy Duty
|
Heavy Duty
|
| Model |
SE4, SE4R
|
SE6, SE6R
|
| Sweep Width |
2000mm
|
2000mm
|
| Brush Diameter |
508mm or 610mm
|
860mm
|
| Sweep Angle |
30° L/R
|
|
| Brush Type |
Poly, Steel, Poly/Steel Mix
|
|
*Available for use with tractor Hydraulic System
or Remote Hydraulics
*Optional Hydraulic Angling
|
Three Point Linkage
To suit tractors up to 16-40H.P.
|
|
| Models
SE2R & SE3R |
|
|
| Model |
SE2R
|
SE3R
|
| Suit Tractor |
16-24 H.P.
|
24-40.H.P.
|
| Sweep Width |
1500mm
|
1800mm
|
| Brush Diameter |
380mm
|
508mm
|
| Sweep Angle |
25° L/R
|
|
| Brush Type |
Poly, Steel, Poly/Steel Mix
|
|
*Light Duty with Remote Hydraulics
|
Three
Point Linkage Collector Brooms
To suit tractors up to 40H.P. and above.
|
|
| Models
SE4C & SE6C |
|
|
| Model |
SE4C
|
SE6C
|
| Sweep Width |
2000mm
|
2100mm
|
| Brush Diameter |
610mm
|
860mm
|
| Sweep Angle |
30° L/R
|
|
| Brush Type |
Poly, Steel, Poly/Steel Mix
|
|
*Hydraulic Systems or Remote Hydraulics
*Optional Hydraulic Angling
|
Quick Hitch
Front End Loader Brooms
To suit Quick Hitch Facility and Tractor
width
| Brush Diameter |
860mm, 610mm and 508mm
|
| Broom Width |
Up to 3600mm
|
| Brush Type |
Poly, Steel, Poly/Steel Mix
|
|
|
| |
|
|
*Solenoid Hydraulic Angling 30° L/R
|
Quick Hitch Collector Broom for Front
End Loader
To suit Front End Loaders from Skid
Steer Loader size and upward
Guaranteed to sweep and collect while
travelling forward for the life of the brush.
|
|
| |
|
|
Features:
Quick Hitch Attachment to suit
Loader width or overwidth as required
Remote Hydraulics
Brush Speed Control
Hydraulic Dump Gate
Options:
Side Broom
Hydraulically Driven Vacuum Fan with Filter for Dust
Suppression
Quick Slash
Easy to connect Slasher for Skid Steer
Loaders
|
Features:
Counter
rotating blades spread the cut grass evenly
eliminating rows of dead
grass.
Rugged
construction with smooth lines.
|
|
| |
|
|
Ideal for Councils and developers
for growth control.
Crushroll
Exclusive one piece roll castings.
Each roll is 1.5 tonne single casting
For low cost, on-site material reduction
and compaction
|
The operation of a Crushroll
enables utilization of oversize pit-run material that
may otherwise be unusable. Material from roadside pits,
quarries, river beds and excavations can be tipped and
spresd directly where required and treated with a Crushroll.
Fine material is allowed to pass through the mesh openings,
and oversize material is shattered by the impact from
cast steel knuckles giving point of contact. Successive
passes also compact that material resulting in well
graded and dense base course. |
|
|
Able to be towed at up to 24 KPH, and having a fully
ballasted weight of 13.7 tonnes, the Crushroll is
a high output machine ideally suited to shire councils,
contractors and other road builders for use on jobs
where suitable material is readily available.
Features:
Replaceable Scrapers
Two Height Towing
Fixed or Swivelling Towbar
Heavy Duty Bearings
Built-in Jacking Leg
|
|
| Technical Data: Crushroll MK3
|
| O/A
Length |
4950 mm
|
| O/A Width |
2290 mm
|
| O/A
Height |
1730 mm
|
| Roll ø |
1730 mm
|
| Roll
Width |
2 x 810 mm
|
| Weight Bare |
6710 mm
|
| Weight
of Sand Ballast in Roll Cones |
1406 mm
|
| Weight of Concrete
or Steel Ballast |
5624 mm
|
| TOTAL
BALLASTED WEIGHT |
13,740 mm
|
| Drawbar Height
2 Positions |
850 mm
420 mm
|
| Drawbar
Reaction (Down) |
135 kg
|
|
|
